manualshive.com logo in svg

Siemens Prisma 3T, User Manual, Page: 48 / 55

Share
Download
Siemens Prisma 3T User Manual Download Page 48

Revision Date:  3/13/2019 

44 
 

 

Then click on the  

Xshell

 

shortcut on the right

 

6.

 

Once the terminal opens click 

Connect

 

7.

 

Then type 

FIRMM

 

to start the software

 

8.

 

The software will take a moment to load

 

9.

 

When FIRMM starts, an X11 terminal should open and you should see a screen like this: 

 

Using FIRMM 

1.

 

Once open, you need to click the start button at the top right of the FIRMM GUI window 
to begin monitoring for DICOMs 
 
 
 
 
 

2.

 

Once FIRMM has been started, it will process each bold sequence 

3.

 

There is about a 40sec delay before data is generated for each bold – the data will start to 
stream from FIRMM around the same time that the inline display shows images 

4.

 

When FIRMM first begins processing, a dialog box will appear asking you to check that 
the participant ID on the FIRMM screen is correct

 

 

 
 
 
 
 

5.

 

If the participant ID is correct for the current session, you may continue 

Summary of Contents for Prisma 3T
























































Reviews:

No comments