manualshive.com logo in svg

Siemens Prisma 3T, User Manual, Page: 40 / 55

Share
Download
Siemens Prisma 3T User Manual Download Page 40

Revision Date:  3/13/2019 

36 
 

Optoacoustics Headphone and Microphone Setup 

 

Positioning the Participant 

1.

 

You may use the Opto headphones with or without earplugs 

2.

 

Position the headphones on the participant and be sure to use pads or paper towels to take 
up the extra space between the headphones and coil (this is especially important if you 
are using the active noise cancellation feature)  

3.

 

Position the microphone if applicable - be sure it is almost touching the participant’s lips 

Setting up the Opto Console 

1.

 

AFTER

 moving the participant into the bore, turn on the Opto control box 

using the black switch on the back right side of the console 

2.

 

Touch the screen to continue 

3.

 

If you are playing audio (movie, music or an audio task) connect the audio 
cable to either the green connection inside the white drawer for the desktop 
computer or to a laptop port – the other end of this should be connected at the 
back of the Opto console in “line 1”  

4.

 

The line 1 (#5) knob controls the volume of this audio 

5.

 

The left button (#4 FORMI NOISE CANCELLER) on the Opto console should always 
be pressed down “On”  

6.

 

The right button (#3) should always be up (in the FORMI position) when talking to the 
participant - otherwise feedback will be generated 

7.

 

During the movie or task you can press the right button down (#3 headphones position) to 
hear what the participant is hearing – just don’t forget to put it back up before talking to 
the participant 

8.

 

To talk to the participant press the bottom silver button (#2)  

9.

 

Use the Siemens talk box to listen to your participant’s responses 

Summary of Contents for Prisma 3T
























































Reviews:

No comments