manualshive.com logo in svg

Siemens Prisma 3T, User Manual, Page: 18 / 55

Share
Download
Siemens Prisma 3T User Manual Download Page 18

Revision Date:  3/13/2019 

14 
 

How to Run the ABCD Phantom QA 

The ABCD phantom should be run at least once per week.  This QA protocol may take 
the place of the daily warmup.  The full version takes 29min and the quick version takes 
16min.   

Setting up the Phantom 

1.

 

Place the spherical ABCD phantom inside 32 (ABCD/HCP protocols) or 64 (Other) head 
coil on top of the white cushion 

2.

 

Place the gray cushion in front to secure the phantom (32ch coil only) 

3.

 

Cushions are located next to the phantom in the bin  

4.

 

The cap of the phantom should be center as if it were the nose – it should line up with the 
laser landmark line on the coil 

5.

 

Secure the top half of the head coil by clicking it in and plugging in cable(s) if necessary 

6.

 

Raise the table 

7.

 

Turn on the laser light and set the landmark to run through the cap 

8.

 

Slide the table fully into the scanner 

9.

 

Close and flip the air seal on the scanner door 
 
 

  

 

 

32 Ch Coil 

64 CH Coil 

Summary of Contents for Prisma 3T
























































Reviews:

No comments