manualshive.com logo in svg

Siemens Prisma 3T, User Manual, Page: 42 / 55

Share
Download
Siemens Prisma 3T User Manual Download Page 42

Revision Date:  3/13/2019 

38 
 

Troubleshooting Tips 

1.

 

If you are using the active noise cancellation and get a “out of range” error this means 
your volume was too high – press the “Stop” wait a couple seconds and then press 
“ANC” again to reactivate the noise cancellation 

2.

 

To reboot the system, turn off the power switch on the back of the console – wait 

at least 

20s

 – then turn it back on 

3.

 

If the participant can only hear out of one ear, check the balance nodes (#11 and # 13) on 
the back behind the line 1/line 2 knobs – make sure it is balanced in the middle  

4.

 

If the participant can’t hear the movie or auditory stimuli check that all the correct cables 
are connected, the sound on the computer is not muted and the line1 dial is turned up, if 
everything is ok reset the system (step#2) to resolve the issue 
 

5.

 

If the participant can’t hear you, you will see a “Laser Fault” 

icon (see icon list 

below) on the screen that says “Start” – this is the first screen after “touch screen to 
continue” – try to reset the system (step#2) to resolve the issue  
 

 

 

Summary of Contents for Prisma 3T
























































Reviews:

No comments