Sharp AR-M236 Service Manual Download Page 66

Page: 66 / 144

AR-M236/M276/M237/M277 SIMULATION 8 - 27

Operation/procedure

Select the short time setup or the long time setup of the pre-heat time
and the auto power shut off time with the 10-key, and press the
[START] key.

Note: When the sub code 71 is entered to display the setting menu,the

default values are always displayed. (However,the default time is
not always set.)

Operation/procedure

Input the set value with the 10-key and press the [START] key.

Operation/procedure

The currently set number is displayed on the PRESENT column.

Enter the new tag number (Max. 8 digits) with the 10-key.
The entered number is displayed on the NEW column.

Press the [START] key.
The set value is stored and "PRESENT" is revised.

Operation/procedure

The active sensors and detectors are highlighted.

Operation/procedure

The active sensors and detectors are highlighted.

Width detection size of the manual feed tray (one of them is displayed.)

A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA,
8K/16K

(At detection, highlighted)

Item

Content

Default

Pre-heat: 1min, auto power shut off: 4min

Preheat: 15min, auto power shut off: 60min

27-1

Purpose

Setting

Function
(Purpose)

Used to set PC/MODEM communication trouble (U7-
00) detection Yes/No.

Section

Communication (RIC/MODEM)

Item

Specifications

Operation mode
(Common)

Item

Content

Default

OFF

In case of the communication trouble, U7-00 is
not displayed.

In case of the communication trouble, U7-00 is
displayed.

27-5

Purpose

Setting

Function (Purpose)

Used to set the tag number.

Item

Data

30-1

Purpose

Operation test/check

Function
(Purpose)

Used to display the sensor status attached to the
machine.

Section

Others

Item

Operation

PPD1H

PS paper detection 1 sensor

PPD1L

PS paper detection 2 sensor

PPD2

Fusing paper sensor

POD1

1st paper exit paper out sensor

DVCH

Developing cartridge detection sensor

DRST

Drum intial detection sensor

DSWR1

Interlock switch (side door)

SFTHP

Shifter home position sensor

POD2

2nd paper exit paper out sensor

TOPF

2nd paper exit full detection sensor

DSWR0

2nd paper exit cover open/close detection sensor

LOEMP

1st paper exit empty detection sensor

DUP2

Reverse path paper sensor

30-2

Purpose

Operation test/check

Function
(Purpose)

Used to display the status of the sensors attached to
the standard cassette and the manual feed tray. (Use
SIM 4-2 for the option cassettes.)
The sensor of an uninstalled cassette is not displayed.

Section

Paper feed

Item

Operation

PED1

1st cassette paper empty sensor

LUD1

1st cassette paper upper limit detection sensor

CD1

1st cassette empty sensor

PED2

2nd cassette paper empty sensor

LUD2

2nd cassette paper upper limit detection sensor

CD2

2nd cassette empty sensor

PFD2

2nd cassette paper pass sensor

DSWR2

2nd cassette right door detection sensor

MPED

Manual tray paper empty detection

MPLS1

Manual tray length detection 1

MPLS2

Manual tray length detection 2

MPLD1

Manual feed paper length detection 1

MPLD2

Manual feed paper length detection 2

Summary of Contents for AR-M236

















































































































































Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands

Sharp AR-M236, Service Manual

Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands