Sharp AR-M236 Service Manual Download Page 68

Page: 68 / 144

AR-M236/M276/M237/M277 SIMULATION 8 - 29

Operation/procedure

The detection output level of each sensor is displayed in real time.

The value in [ ] shows the threshold value of 20 degree detection
adjustment. (Hexadecimal display)

For AB series, 1 to 5 is displayed, for inch series, 1 to 4.

Operation/procedure

Set the OC cover at 20 degrees detection and press the [START] key.

The detection output level of each sensor is displayed in real time.

The value in [ ] shows the threshold value of 20 degree detection
adjustment. (Hexadecimal display)

For AB series, 1 to 5 is displayed, for inch series, 1 to 4.

During execution, [EXEC] is highlighted.

Operation/procedure

Touch the item to be set.

Enter the set value with the 10-key.

Operation/procedure

Input the set value with the 10-key and press the [START] key.

Operation/procedure

Enter the set value with the 10-key, and press the [START] key.

41-3

Purpose

Operation test/check

Function
(Purpose)

Used to check the light reception level and the
detection level of the original size detection photo
sensor.

Section

Others

Item

Operation

OCSW

Original cover state
Open: Highlighted display
Close: Normal display

1 to 5

PD sensor detection level (Hexadecimal display)

41-4

Purpose

Adjustment

Function
(Purpose)

Used to adjust the detection level of OC 20 degrees.

Section

Others

Item

Operation

OCSW

Original cover state
Open: Highlighted display
Close: Normal display

1 to 5

PD sensor detection level (Hexadecimal display)

43-1

Purpose

Setting

Function
(Purpose)

Used to set the fusing temperature in 600dpi, 1200dpi,
or postcard print.

Section

Fixing (Fusing)

Item

Operation

Item

Content

Setting

range

Default

600dpi

155-200

190 (Europe)/

175 (Japan, SEC,

SECL)/

185 (Others)

1200dpi

140-200

165

POST CARD

Postcard

155-200

190

CARDBOARD

Thick paper

155-200

190

43-10

Purpose

Setting

Function
(Purpose)

Used to set the paper feed cycle timing when printing
postcards.

Section

Paper feed

Item

Operation

Setting range

1-99

Default

44-1

Purpose

Setting

Function
(Purpose)

Used to make various setups in each mode of process
control.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Item

Operation

Item

Content

Default

1 ENVIRONMENT

ADJ.

Environmental correction Allow/
Inhibit (0: Inhibit, 1: Allow)

2 DUPLEX PRINT ADJ. Duplex print correction Allow/

Inhibit (0: Inhibit, 1: Allow)

Summary of Contents for AR-M236

















































































































































Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands

Sharp AR-M236, Service Manual

Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands