Sharp AR-M236 Service Manual Download Page 105

Page: 105 / 144

AR-M236/M276/M237/M277 DISASSEMBLY, ASSEMBLY AND MAINTENANCE 10 - 4

∗

When assembling, check that the hook is securely engaged in two
positions.

(2) DV seal/side seal

[DV seal attachment procedure]

1) When attaching the DV side Mylar, check the position shown in the

figure below and attach it properly.

2) When attaching the DV side seal, check the position shown in the

figure below and attach it properly.
(First of all, attach the DV side Mylar.)

The attachment reference is the same, but the area of the N2
shape is reduced to half as shown with the red square in the above
figure.

∗

Be sure to attach the DV side sheet so that the notch is on the out-
side.

Note: Attach it to fit with the attachment reference when replacing the

DV seal.

(3) DV moquette/Toner sensor

a. DV moquette

b. Toner sensor

• Clean the sensor only after removing used DV when replacing DV.

• There is no need to remove the MG roller as shown in the above fig-

ure. Use waste cloth to remove toner from the sensor surface in the
arrow direction shown in the figure below.

∗

Attaching reference

Side seal

DV seal

Faulting

Attaching
reference

Gluing

face

0.5

DV moquette

Toner sensor

MG roller

Summary of Contents for AR-M236

















































































































































Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands

Sharp AR-M236, Service Manual

Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands