Sharp AR-M236 Service Manual Download Page 100 | Manualshive

Page: 100 / 144

background image

AR-M236/M276/M237/M277 TROUBLE CODE LIST 9 - 9

L4

11

Content

Shifter motor trouble

Details

The shifter home position detection signal
is not detected when the shifter is
operating.

Cause

Shifter motor trouble or harness
connection trouble and disconnection
Shifter home position sensor trouble

Check
and
remedy

Check the shifter motor operation with SIM
3-11.
Check connection of the shifter motor
harness/connector.
Replace the shifter motor.
Replace the MCU PWB.

L6

10

Content

Polygon motor lock trouble

Details

The polygon motor does not rotate.
The motor lock signal is detected for 6sec
or more after the polygon motor rotates.
The motor lock signal is detected for 1sec
during rotation of the polygon motor.

Cause

Polygon motor unit failure
Polygon motor connection, harness
trouble or disconnection
MCU PWB failure

Check
and
remedy

Check the polygon motor operation with
SIM 61-1.
Check connector/harness of polygon
motor
Replace the polygon motor.
Replace the MCU PWB.

L8

10

Content

Power abnormality detection trouble

Details

The power status monitoring signal keeps
power OFF state after passing the
specified time (2sec).

Cause

Circuit around the power status monitoring
signal failure.

Check
and
remedy

Check whether power status monitoring
signal on MCU PWB is OPEN or not.
Replace MCU PWB.

U1

01

Content

FAX battery error

Details

The SRAM backup battery voltage on FAX
PWB falls.

Cause

The SRAM backup battery voltage on FAX
PWB falls.

Check
and
remedy

Check voltage of the SRAM back up
battery.
Replace the battery.

02

Content

PANEL LOW battery error

Details

The voltage of the panel clock function
battery falls.

Cause

The voltage of the panel clock function
battery falls.

Check
and
remedy

Check voltage of panel clock function
battery.
Replace the battery.

U2

04

Content

EEPROM communication error

Details

MCU PWB EEPROM access circuit failure

Cause

EEPROM defective
ICU PWB EEPROM access circuit failure

Check
and
remedy

Check that the EEPROM is properly set.
Clear trouble with SIM 16.
Replace the MCU PWB.

Remarks

EEPROM abnormality

Trouble

code

Details of trouble

Main
code

Sub

code

U2

20

Content

Machine speed code data error

Details

The machine (Boot) speed information is
not identical to the model code speed
information.

Cause

EEPROM defective
SIM operation error

Check
and
remedy

Check that the machine set with SIM 26-
57 is identical to the model information.

Remarks

When the boot program speed code does
not match with the body model
information.

40

Content

CRUM chip communication error

Details

Error in MCU-CRUM chip communication

Cause

CRUM chip failure
Developing unit contact trouble
MCU PWB failure

Check
and
remedy

Replace the CRUM chip.
Check installation of the developing unit.
Clear the trouble with SIM 16.
Replace the MCU PWB.

Remarks

CRUM communication error

U7

00

Content

RIC communication trouble

Details

Error in communication with RIC
Error in communication test after turning
on the power or canceling SIM.

Cause

Connector harness contact trouble or
disconnection
RIC control PWB trouble
MCU PWB failure
Malfunction by noises

Check
and
remedy

Check the communication cable,
connectors from the RIC box to the main
body.

U9

00

Content

MCU-OPE communication trouble

Details

Communication establishment error/
framing/parity/protocol error

Cause

Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure

Check
and
remedy

Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on the operation control
PWB.

80

Content

Operation control PWB communication
trouble (Protocol)

Details

Communication trouble between MCU and
the operation control PWB (Protocol error)

Cause

Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure

Check
and
remedy

Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.

Trouble

code

Details of trouble

Main
code

Sub

code

«
...
98
99
100
101
102
...
»

Summary of Contents for AR-M236

















































































































































Reviews:

No comments

Related manuals for AR-M236

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 8

KX-FLB851 - All-in-One Flatbed Laser Fax

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: TallyGenicom Pages: 3

Brand: Oki Pages: 32

Brand: Oki Pages: 2

Brand: Oki Pages: 96

Brand: Oki Pages: 2

Brand: Oki Pages: 78

Brand: Oki Pages: 2

Brand: Oki Pages: 2

Brand: Oki Pages: 32

Brand: Oki Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands