Sharp AR-M236 Service Manual Download Page 52

Page: 52 / 144

AR-M236/M276/M237/M277 SIMULATION 8 - 13

Operation/procedure

Touch the exposure mode to be changed.
The current set value is highlighted.

Enter the set value with the 10-key.

Press the [START] key.

Output is made with the entered value for 30sec, and the display
returns to the original state.

Min. unit: 25V increment

*1. The negative value of the set value corresponds to the grid high

output voltage.

*2. The set values can be selected from the above 8 patterns only.

*3. The selected pattern determines the grid high voltage and the grid

low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.

Operation/procedure

Touch the exposure mode to be changed.
The current set value is highlighted.

Enter the set value with the 10-key.

Press the [START] key.

Output is made with the entered value for 30sec, and the display
returns to the original state.

Min. unit: 25V increment

*1. The negative value of the set value corresponds to the grid high

output voltage.

*2. The set values can be selected from the above 8 patterns only.

*3. The selected pattern determines the grid high voltage and the grid

low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.

Operation/procedure

Enter the set value with the 10-key.

Press the [START] key.

Output is made with the entered value for 30sec. and the display
returns to the original state.

8-11

Purpose

Adjustment/Operation test/check

Function
(Purpose)

Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer mode
and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Photo conductor

Item

Content

Installation

range

Default

DENS1(600)

Density 1 (600dpi)

1-8

5 (–580V)

DENS2(600)

Density 2 (600dpi)

5 (–580V)

DENS3(600)

Density 3 (600dpi)

5 (–580V)

DENS4(600)

Density 4 (600dpi)

5 (–580V)

DENS5(600)

Density 5 (600dpi)

7 (–630V)

TS(600)

Toner save (600dpi)

3 (–530V)

DENS1(1200)

Density 1 (1200dpi)

1 (–480V)

DENS2(1200)

Density 2 (1200dpi)

3 (–530V)

DENS3(1200)

Density 3 (1200dpi)

4 (–555V)

10 DENS4(1200)

Density 4 (1200dpi)

5 (–580V)

11 DENS5(1200)

Density 5 (1200dpi)

7 (–630V)

NO.

Set value

Grid High

Grid Low

1 480

–480V

–350V

2 505

–505V

–375V

530

–530V

–400V

555

–555V

–425V

580

–580V

–450V

6 605

–605V

–475V

7 630

–630V

–500V

8 655 –655V

–525V

8-12

Purpose

Adjustment/Operation test/check

Function
(Purpose)

Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer mode
and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)
Photo conductor

Item

Content

Installation

range

Default

DENS1(600)

Density 1 (600dpi)

1-8

5 (–450V)

DENS2(600)

Density 2 (600dpi)

5 (–450V)

DENS3(600)

Density 3 (600dpi)

5 (–450V)

DENS4(600)

Density 4 (600dpi)

5 (–450V)

DENS5(600)

Density 5 (600dpi)

7 (–500V)

TS(600)

Toner save (600dpi)

3 (–400V)

DENS1(1200)

Density 1 (1200dpi)

1 (–350V)

DENS2(1200)

Density 2 (1200dpi)

3 (–400V)

DENS3(1200)

Density 3 (1200dpi)

4 (–425V)

DENS4(1200)

Density 4 (1200dpi)

5 (–450V)

DENS5(1200)

Density 5 (1200dpi)

7 (–500V)

NO.

Set value

Grid High

Grid Low

1 480

–480V

–350V

2 505

–505V

–375V

530

–530V

–400V

555

–555V

–425V

580

–580V

–450V

6 605

–605V

–475V

7 630

–630V

–500V

8 655 –655V

–525V

8-13

Purpose

Adjustment/Operation test/check

Function
(Purpose)

Used to check and adjust the operation of the
developing bias voltage in FAX mode and the control
circuit.

Section

Image process (Photoconductor/Developing/Transfer/
Cleaning)

Developer/Toner hopper

Setting range

200-550

Default

426

Summary of Contents for AR-M236

















































































































































Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands

Sharp AR-M236, Service Manual

Search results

Summary of Contents for AR-M236

Reviews:

Related manuals for AR-M236

Brands by name

Popular brands