manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Manual

Share
Download
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Manual Download Page 3

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card

3

1 Important Notes...................................................................................................... 4

2 Introduction ............................................................................................................ 5

3 Assembly / Installation Instructions................................................................... 10

3.1

Installing the DHP11B control card .............................................................. 10

3.2

Connection and terminal description of the DHP11B control card ............... 12

3.3

Connecting binary inputs and outputs (connector X31) ............................... 13

3.4

Connecting CAN 2 system bus (connector X32).......................................... 14

3.5

Connecting CAN 1 system bus (connector X33).......................................... 15

3.6

Connecting PROFIBUS (connector X30) ..................................................... 16

3.7

Connection of RS485 interface (connector X34).......................................... 19

3.8

Operating display of the DHP11B control card ............................................ 20

3.9

GSD file........................................................................................................ 23

4 Project Planning and Startup .............................................................................. 24

4.1

Engineering interfaces of the DHP11B control card..................................... 24

4.2

Connecting the drive inverter via system bus CAN 1 / CAN 2 ..................... 24

4.3

Starting the programming software .............................................................. 25

4.4

Project planning for the PROFIBUS DP master........................................... 26

5 PROFIBUS-DP Operating Characteristics.......................................................... 35

5.1

Process data exchange with the DHP11B control card ............................... 35

5.2

PROFIBUS-DP timeout................................................................................ 37

5.3

Parameter setting via PROFIBUS-DP.......................................................... 38

5.4

Return codes for parameter setting.............................................................. 42

5.5

Special cases ............................................................................................... 43

6 DP-V1 Functions................................................................................................... 45

6.1

Introduction to PROFIBUS DP-V1 ............................................................... 45

6.2

Features of the SEW DP-V1 interfaces........................................................ 47

6.3

Structure of the DP-V1 parameter channel .................................................. 48

6.4

Project planning for a C1 master.................................................................. 61

6.5

Appendix ...................................................................................................... 61

7 Error Diagnostics ................................................................................................. 63

7.1

Diagnostic procedure for system buses CAN 1 / CAN 2.............................. 63

7.2

Diagnostic procedure for PROFIBUS-DP .................................................... 64

8 Technical Data ...................................................................................................... 65

8.1

DHP11B control card ................................................................................... 65

9 Index ...................................................................................................................... 68

Summary of Contents for MOVIDRIVE MOVI-PLC DHP11B

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands