manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Manual

Share
Download
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Manual Download Page 11

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card 

11

3

Installing the DHP11B control card

Assembly / Installation Instructions

Basic procedure for installing/removing an option card

1. Remove the retaining screws holding the card retaining bracket. Pull the card retain-

ing bracket out evenly from the slot (do not twist).

2. Remove the retaining screws of the black cover plate on the card retaining bracket.

Remove the black cover plate.

3. Position the DHP11B option card onto the retaining bracket so that the retaining

screws fit into the corresponding bores on the card retaining bracket. 

4. Insert the retaining bracket with installed option card into the slot, pressing slightly so

it is seated properly. Secure the card retaining bracket with the retaining screws.

5. Follow the instructions in reverse order when removing the option card.

53001AXX

Figure 3: Basic procedure for installing an option card in MOVIDRIVE

®

 MDX61B sizes 1-6

1.

3.

4.

2.

Summary of Contents for MOVIDRIVE MOVI-PLC DHP11B

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands