manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Manual

Share
Download
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Manual Download Page 4

4

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card

1

Important Notes

Manual

1

Important Notes

Documentation

•

Read through this manual carefully before you start installation and startup of the
control card type DHP11B.

•

This manual assumes that the user has access to and is familiar with the
MOVIDRIVE

®

 documentation, in particular the MOVIDRIVE

®

 MDX60B/61B system

manual.

•

In this manual, cross references are marked with "

→

". For example, (

→

 Sec. X.X)

means: Further information can be found in section X.X of this manual.

•

A requirement of fault-free operation and fulfillment of any rights to claim under guar-
antee is that you observe the information in the documentation.

Bus systems

General safety notes for bus systems:

This communication system allows you to adjust the type DHP11B control card to meet
the exact specifications of your application. As with all bus systems, there is a danger of
invisible, external (as far as the type DHP11B control card is concerned) modifications
to the parameters which give rise to changes in the inverter behavior. This may result in
unexpected (not uncontrolled) system behavior.

Safety and 
warning notes

Always observe the safety and warning instructions contained in this publication!

•

This manual does not replace the detailed operating instructions!

•

Only specialists are allowed to perform installation and startup observing
relevant accident prevention regulations and the MOVIDRIVE

®

 MDX60B/61B

operating instructions!

Electrical hazard
Possible consequences: Severe or fatal injuries.

Hazard 
Possible consequences: Severe or fatal injuries.

Hazardous situation
Possible consequences: Slight or minor injuries.

Harmful situation
Possible consequences: Damage to the unit and the 
environment.

Tips and useful information.

Summary of Contents for MOVIDRIVE MOVI-PLC DHP11B

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands