manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Manual

Share
Download
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Manual Download Page 43

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card 

43

5

Special cases

PROFIBUS-DP Operating Characteristics

Error code

The 

error code

 element provides a means of identifying the cause of the error within the

error class

. It is generated by the communication software of the fieldbus card in the

event of an error in communication. For 

Error class 8 = Other error

, only 

Error code = 0

(Other error code)

 is defined. In this case, detailed identification is made using the

additional code

.

Additional code

The 

additional code

 contains SEW-specific return codes for errors in the DHP11B con-

trol card. These codes are returned to the master under 

Error class 8 = Other error

. The

following table shows all possible codes for the 

additional code

.

5.5

Special cases

Special return 
codes

Errors in parameter settings that cannot be identified either automatically by the appli-
cation layer of the fieldbus system or by the system software of the DHP11B control card
are treated as special cases. The following errors can occur depending on the control
card used:

•

Incorrect coding of a service via parameter channel

•

Incorrect length specification of a service via parameter channel

•

Internal communication error

Add. code 
high (hex)

Add. code low 
(hex)

Description

00

00

No error

00

10

Illegal parameter index

00

11

Function / parameter not implemented

00

12

Read access only

00

13

Parameter lock is active

00

14

Factory setting is active

00

15

Value for parameter too large

00

16

Value for parameter too small

00

17

Reserved

00

18

Error in system software

00

19

Reserved

00

1A

Parameter access only via RS485 interface

00

1B

Parameter is access-protected

00

1C

Reserved

00

1D

Invalid value for parameter

00

1E

Factory setting was activated

00

1F

Reserved

00

20

Reserved

0

0

I

Summary of Contents for MOVIDRIVE MOVI-PLC DHP11B

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands