manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Manual

Share
Download
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Manual Download Page 63

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card 

63

7

Diagnostic procedure for system buses CAN 1 / CAN 2

Error Diagnostics

7

Error Diagnostics

7.1

Diagnostic procedure for system buses CAN 1 / CAN 2

Diagnostic problem: Communication via system bus CAN 1 or CAN 2 
does not work.
Initial status:
•

System bus CAN 1 or CAN 2 is connected correctly.

•

Communication via system bus CAN 1 or CAN 2 is programmed.

↓

Is the bus connector plugged in?

No 

→

[A]

Yes

↓

Response of the LEDs CAN 1 status 

or CAN 2 status?

Orange 

→

[B]

Green 

→

[C]

Lights up or flashes red

↓

System bus CAN 1 or CAN 2 is not operating
or communication of the system bus is faulty.

↓

[A]

↓

Check the set baud rate.

↓

Baud rate OK?

No 

→

[D]

Yes

↓

Make sure that terminating resistors are connected properly.

[A]

Check the bus cabling!

[B]

System bus CAN 1 or CAN 2 is being initialized.

[C]

Bus communication is OK. 

↓

Check the application program!

[D]

Correct the baud rate!

Summary of Contents for MOVIDRIVE MOVI-PLC DHP11B

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands