SEPTENTRIO PolaRx5TR Reference Manual Download Page 399

Page: 399 / 512

4 SBF Reference

Parameter

Type Units

Do-Not-Use

Description

Sync1

Block Header, see 4.1.1

Sync2

CRC

Length

byte

TOW

0.001

4294967295

Receiver time stamp, see 4.1.3

WNc

week

65535

Mode

Bit ﬁeld indicating the GNSS PVT mode, as follows:
Bits 0-3: type of PVT solution:

No GNSS PVT available (the

Error

ﬁeld indicates the

cause of the absence of the PVT solution)

Stand-Alone PVT

Differential PVT

Fixed location

RTK with ﬁxed ambiguities

RTK with ﬂoat ambiguities

SBAS aided PVT

moving-base RTK with ﬁxed ambiguities

moving-base RTK with ﬂoat ambiguities

10:

Precise Point Positioning (PPP)

12:

Reserved

Bits 4-5: Reserved
Bit 6:

Set if the user has entered the command

setPVTMode,

Static, , auto

and the receiver is still in the process of de-

termining its ﬁxed position.

Bit 7:

2D/3D ﬂag: set in 2D mode (height assumed constant and not

computed).

Error

PVT error code. The following values are deﬁned:

No Error

Not enough measurements

Not enough ephemerides available

DOP too large (larger than 15)

Sum of squared residuals too large

No convergence

Not enough measurements after outlier rejection

Position output prohibited due to export laws

Not enough differential corrections available

Base station coordinates unavailable

10:

Ambiguities not ﬁxed and user requested to only output RTK-

ﬁxed positions

−

X coordinate in coordinate frame speciﬁed by

Datum

−

Y coordinate in coordinate frame speciﬁed by

Datum

−

Z coordinate in coordinate frame speciﬁed by

Datum

Base2RoverX

−

X baseline component (from base to rover)

Base2RoverY

−

Y baseline component (from base to rover)

Base2RoverZ

−

Z baseline component (from base to rover)

Cov_xx

−

Variance of the x estimate

Cov_yy

−

Variance of the y estimate

Cov_zz

−

Variance of the z estimate

Cov_xy

−

Covariance between the x and y estimates

Cov_xz

−

Covariance between the x and z estimates

Cov_yz

−

Covariance between the y and z estimates

PDOP

0.01

If 0, PDOP not available, otherwise divide by 100 to obtain PDOP.

HDOP

0.01

If 0, HDOP not available, otherwise divide by 100 to obtain HDOP.

VDOP

0.01

If 0, VDOP not available, otherwise divide by 100 to obtain VDOP.

399

Summary of Contents for PolaRx5TR

































































































































































































































































































































































































































































































































Search results

Summary of Contents for PolaRx5TR

Reviews:

Related manuals for PolaRx5TR

Brands by name

Popular brands

SEPTENTRIO PolaRx5TR, Reference Manual

Search results

Summary of Contents for PolaRx5TR

Reviews:

Related manuals for PolaRx5TR

Brands by name

Popular brands