ASSEMBL
Y
AND INST
ALLA
TION
ENGAGEMENT OF POWER SUPPLY AFTER INSTALLING SOFTWARE
It takes about 2 minutes and 30 seconds for initialization to complete after the
power has been engaged. Do not touch the product or press any buttons until
after initialization is completed. If an anomaly is detected during initialization,
there is an error display. Unless the cause of the error is removed and initialization
is allowed to complete normally, the product will not operate properly.
Only engage the power supply after checking the surroundings. Initialization takes
place automatically when engaging the power supply after software installation.
At this time the seat will move, and if anyone is near the product, they may collide
with the product, fall down, or get their hand or finger caught somewhere.
Set the main switch of the AC unit to ON and engage the power. When the power is engaged, 1 fluorescent lamp in
the billboard and 2 fluorescent lamps on the seat rear surface will light up.
After the LINDBERGH start-up screen has appeared, the “initialization in progress” screen appears and initialization
begins. During initialization the seat moves automatically in the following sequence and stops at the preset values
for position and direction.
1
Seat tilts slightly to the left and right.
Seat tilts to the limit on the right side.
Seat tilts to the limit on the left side.
Seat stops at the level position.
Upon completion of initialization, the Attract (waiting for customers) Mode screen is displayed. The Attract Mode
demo appears on the monitor and sound is output from the speakers to the left and right of the monitor and to the left
and right of the seat backrest. The LEDs at the upper right and left of the monitor also light up.
If the unit is set for no sound during Attract Mode, there is no sound output.
If there are enough credits to enable play, the start button on the control panel flashes. It goes out if there are no
credits during Attract Mode.
If the setting is for network play, the screen for “checking network” message appears on the monitor after completion
of initialization.
If there are no problems with the connections or settings for network play, the Attract Mode screen appears.
If there are any anomalies or faults in the connections or settings for network play, the confirmation screen or error
message is displayed. Inspect the connections and settings of the cable for network play.
Upon completion of initialization, if the seat inclines and stops, for instance, re-engage the power source and execute
initialization once again.
Summary of Contents for AFTER BURNER CLIMAX
