Sea-doo 1997 GS Operator'S Manual Download

Page: 74 / 105

Periodic Inspection Chart

NOTE:

Some items are included

in the PRE-OPERATION CHECKS

and not necessarily repeated in this
chart.

➀

Every 10 hours in salt water use.

➁

These items have to be initially
checked after 25 hours. Thereafter,
servicing to be made as specified in
this chart.

➂

Daily flushing in salt water or foul
water use.

DESCRIPTION

FREQUENCY

eve

10 hour

eve

25 hour

eve

50 hour

eve

100 hou

seasonal

To be

performed

Lubrication/corrosion protection

➀

✔

OPERATOR

Engine ignition timing

✔

DEALER

Spark plug replacement

✔

DEALER

Throttle/choke cables, inspection/lubrication

➀

✔

OPERATOR

Flame arrester inspection

✔

DEALER

Carburetor adjustment including choke/throttle cable
adjustments

✔

DEALER

Oil injection pump adjustment

✔

DEALER

Fuel filter and oil filter inspection

✔

DEALER

Fuel filter and oil filter replacement

✔

DEALER

Fuel reservoir straps

✔

OPERATOR

Oil reservoir straps

✔

OPERATOR

Engine head bolts, retorque

✔

DEALER

Steering system

✔

DEALER

Reverse system/reverse cable adjustment
(GTS/GTI/GTX)

✔

DEALER

Variable Trim System (SPX/GSI/GSX/XP)

✔

DEALER

Fastener tightening (flame arrester, carburetor(s),
engine mount, exhaust system, etc.)

✔

DEALER

Muffler, battery and reservoir fastening devices

✔

OPERATOR

Fuel lines, check-valve and fuel system pressurization

✔

DEALER

Fuel vent line pressure relief valve inspection

✔

DEALER

Inspect/clean engine drain tube

➀

✔

DEALER

Bilge system/water tank trap drains inspection
(GSI/GTS/GTI/GTX)

✔

OPERATOR

Battery condition

✔

DEALER

Electrical connections (battery, starter, etc.)

✔

DEALER

Monitoring beeper

✔

DEALER

Impeller shaft reservoir oil level/oil condition

✔

Replace

DEALER

Impeller condition and impeller/wear ring clearance

✔ ➁

DEALER

Drive shaft boot and spline condition (both ends)

✔ ➁

DEALER

PTO flywheel lubrication

✔

OPERATOR

Water intake grate condition

✔ ➁

OPERATOR

Hull condition

✔

OPERATOR

Cooling system flushing

✔➂

OPERATOR

smo9701a.bk : smo9701b.fm5 Page 72 Monday, November 3, 1997 9:54 AM

www.SeaDooManuals.net

Summary of Contents for 1997 GS









































































































Search results

Summary of Contents for 1997 GS

Reviews:

Related manuals for 1997 GS

Brands by name

Popular brands

Sea-doo 1997 GS, Operator'S Manual

Search results

Summary of Contents for 1997 GS

Reviews:

Related manuals for 1997 GS

Brands by name

Popular brands