Sea-doo 1997 GS Operator'S Manual Download | Manualshive

Page: 69 / 105

background image

67

Capsized Watercraft

SP Series

The watercraft is designed so that if it
is turned over, it should not remain
capsized due to its self-righting capa-
bility.

After roll over, always tip watercraft
counterclockwise (maximum 90°) be-
fore restarting engine.

GS Series/GTS/GTI/GTX/HX/XP
Models

The watercraft is designed so that it
should not turn over easily, due to its
longer and larger dimensions and its
full vee hull. Also two sponsons
mounted on the side of the hull assist
watercraft stability. If it turns over, it
will remain capsized due to its non
self-righting capability. To return the
watercraft upright rotate it

clockwise

(seen from rear) by pushing on the
right side then handhold the side of
water intake

HOLE

and use your

weight to complete the rotation of wa-
tercraft.

Submerged Watercraft

If the watercraft is submerged and en-
gine is water-flooded, it is strongly rec-
ommended that the watercraft be ser-
viced by an authorized dealer im-
mediately.

In the event the engine cannot be ser-
viced within a few hours, remove
spark plug cables and connect them
on the grounding device.

Remove spark plugs and dry them
with a clean and dry cloth.

Cover spark plug holes with a rag.

Crank engine to allow water to escape
from spark plug openings.

Spray BOMBARDIER LUBE lubricant
into spark plug holes.

Crank engine again.

Reinstall spark plugs.

XP/GSX/GTX

Remove balancing shaft drain plug.
Ensure that there is no water contam-
ination.

Re-install drain plug.

Add 30 ml (1 oz) of Formula XP-S syn-
thetic injection oil through filler plug.

-

CAUTION

Inspect water intake grate for
damage. Refer to an authorized
dealer for repair as necessary.

-

CAUTION

Avoid watercraft operation in
weeded areas. If unavoidable,
vary watercraft speed. Weeds
tend to entangle more at steady
speed and at slow speed.

-

CAUTION

Always refer to decal located on
stern of watercraft before tipping
over.

◆

WARNING

Never crank engine with spark
plugs removed unless spark plug
cables are connected to the
grounding device.

F02L1ZY

smo9701a.bk : smo9701b.fm5 Page 67 Monday, November 3, 1997 9:54 AM

www.SeaDooManuals.net

«
...
67
68
69
70
71
...
»

Summary of Contents for 1997 GS










































































































Reviews:

No comments

Related manuals for 1997 GS

TomCat 255 Pilothouse

Brand: C-Dory Marine Pages: 20

foundation series

Brand: Quickboats Pages: 22

Brand: grabner Pages: 24

2012 Cobia 21 Bay

Brand: Maverick Boat Company Pages: 22

Brand: BRIG Pages: 36

Brand: Malibu Boats Pages: 164

Brand: Hunter Pages: 157

Brand: Alliaura Marine Pages: 44

Brand: YAMARIN Pages: 44

Brand: World Cat Pages: 101

Brand: 3D Tender Pages: 23

Brand: Performance Cruising Pages: 59

Brand: Trophy Pages: 64

Whitewater Series

Brand: Dagger Pages: 12

Brand: BENETEAU Pages: 43

Brand: Ranger Tugs Pages: 40

Brand: West Marine Pages: 20

Brand: Sea Ray Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands