Sea-doo 1997 GS Operator'S Manual Download | Manualshive

Page: 23 / 105

background image

21

TYPICAL

TYPICAL

TYPICAL

TYPICAL

TYPICAL

TYPICAL

Meeting head on:
KEEP RIGHT.

Passing: Give right
of way to other boat
and KEEP CLEAR.

Crossing: GIVE
RIGHT OF WAY to
boats ahead and to
your right (see Yield
Zone). Never cross
in front of a boat.

REMEMBER THESE RULES OF THE ROAD

WARNING

Read all warning labels,

Operator Guide, & Safety Handbook before

operation. Severe injury or death can result from ignoring warnings or

through improper use of this watercraft.

• Check throttle & steering operation before starting engine.
• Directional control is lost when throttle is released or engine shut off.
• Do not splash others or jump waves or wakes with this watercraft.
• Operator and passenger should always wear approved life vests and recommended clothing.
• Gasoline is explosive. Always observe proper fueling practices and maintenance.
• Properly attach safety lanyard to your life vest.
• This watercraft is not designed for night-time operation.
• Seating is limited to one operator and one passenger (350 lbs.)
• Keep a safe distance from all other water users. Be aware of all boating regulations.

starboard

port

bow

stern

YIELD

ZONE

F01L6TM

3

TO CLOSE / POUR FERMER

F06A03Y

4

F01L6VY

5

WARNING

WHILE FUELING, STOP ENGINE. FUEL TANK MAY BE
PRESSURIZED, SLOWLY TURN CAP WHEN OPENING.
KEEP WATERCRAFT LEVEL. DO NOT OVERFILL. CHECK
OIL LEVEL. PERIODICALLY, VERIFY FUEL SYSTEM.

F02L2CY

2

WARNING

DO NOT BOOST BATTERY.
SERVICING OF ELECTRICAL COMPONENTS
SHOULD BE DONE BY DEALER ONLY.

F02L2C1

6

WARNING

DO NOT BOOST BATTERY.
SERVICING OF ELECTRICAL COMPONENTS
SHOULD BE DONE BY DEALER ONLY.

TO AVOID POSSIBLE ENGINE FLOODING WHEN ROLLED OVER :

MAKE SURE ENGINE IS OFF

GRAB INLET GRATE AND STEP
ON BUMPER RAIL

ROLL BOAT CLOCKWISE

CAUTION

F02L2EY

7

F01L6UY

8

AFTER ROLL OVER

ALWAYS TIP
WATERCRAFT
AS SHOWN
BEFORE
RESTARTING
ENGINE

smo9701b.fm5 Page 21 Thursday, November 13, 1997 9:44 AM

www.SeaDooManuals.net

«
...
21
22
23
24
25
...
»

Summary of Contents for 1997 GS










































































































Reviews:

No comments

Related manuals for 1997 GS

2270 CENTER CONSOLE

Brand: PURSUIT Pages: 104

BARF BALL 2091532

Brand: O'Brien Pages: 14

Brand: RTM Pages: 26

Brand: Scout Boats Pages: 112

Alice Bavaria Cruiser 51 2016

Brand: Hermes Yachting Pages: 25

Brand: Grady-White Pages: 78

Brand: Grady-White Pages: 102

Brand: GALA Pages: 10

Brand: Prestige Pages: 112

Ocean Runner 290

Brand: Mercury Pages: 46

Brand: Scarab Pages: 156

Brand: Polaris Pages: 114

Brand: Polaris Pages: 121

CAP CAMARAT 7.5 WA series 2

Brand: Jeanneau Pages: 112

Brand: Quicksilver Pages: 53

Brand: Yamaha Pages: 277

Brand: Meridian Yachts Pages: 104

Brand: Meridian Yachts Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands