Scout Boats 145 Owner'S Manual Download Page 81 | Manualshive

Page: 81 / 112

background image

Scout Boats

7-5

Care and Maintenance

CORROSION PROTECTION

Galvanic Corrosion

Galvanic corrosion (electrolysis), is the break-up of metals due to the effects
of electrolytic action. When two dissimilar metals are immersed in a
conductive fluid such as salt water, an electric current is produced, much
like a battery. As the current flows, it takes with it tiny bits of the softer
metal. If not stopped, a great deal of damage could occur.

If you operate in salt, polluted, or brackish waters, your boat should be
equip ped with a transom mounted zinc anode to prevent damage to those
metal parts coming in contact with the water. By design, the anode is self-
sacrificing. It is slowly eroded away by electrolytic action and requires peri -
odic inspection for deterioration. If the zinc shows extreme erosion, it must
be replaced for continued protection.

Most engines are equipped with one or more zinc anodes which must also
be inspected regularly for deterioration. Some boat models may be
equipped with an electronic cathode system. This system emits a low
current electrical charge into the water close to the metal components. This
charge cancels the effect of electrolysis.

Never paint or coat zinc anodes or cathodes with any sub -
stance. Once covered, they do not provide protection from
galvanic corrosion. Replace anodes if they have deteriorated
50% or more.

Salt Water Corrosion

The entire boat should be rinsed with fresh water and washed immediately
after use in salt water. If the boat is used primarily in salt water, wax the hull
monthly and apply corrosion inhibitor to all hardware. See your dealer for
products suitable for the marine salt water environment. Fresh water
internal flushing is recommended when used in salt, polluted, or brackish
waters. Flush the entire engine cooling system with fresh water for at least
5 minutes after use in these waters. See your dealer for appropriate
flushing devices.

CAUTION

Scout Boats Section 7.qxd:Scout Boats Section 7.qxd 5/11/07 5:42 AM Page 5

«
...
79
80
81
82
83
...
»

Summary of Contents for 145

















































































































Reviews:

No comments

Related manuals for 145

Pathfinder 2300 HPS

Brand: Maverick Boat Company Pages: 20

Brand: Blue Wave Pages: 22

Brand: Hunter Pages: 216

Brand: TAKACAT Pages: 11

Brand: Lagoon Pages: 122

WaveRunner VXS 2014

Brand: Yamaha Pages: 98

Brand: ANYTEC Pages: 84

Brand: Bayliner Pages: 25

Brand: UpRoar Pages: 31

Brand: Scout Boats Pages: 202

Brand: Scout Boats Pages: 210

Brand: Silver Marine Pages: 13

Brand: Silver Marine Pages: 15

Brand: Silver Marine Pages: 40

Brand: Silver Marine Pages: 75

Brand: Silver Marine Pages: 81

Brand: RS Pages: 28

Brand: MARKER ONE Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands