Scout Boats 145 Owner'S Manual Download Page 101 | Manualshive

Page: 101 / 112

background image

Scout Boats

10-7

Trailering

Excessive throttle can cause the boat to travel over the bumper
board causing extensive damage to the boat, trailer, and car
and could cause severe personal injury.

4. Using a very light touch on the throttle, ease the boat forward until the

bow comes to rest against the bow stop (bumper board).

The winch bow strap is merely a means of securing the boat to
the trailer and is not intended to winch or pull the boat onto the
trailer. Winching the boat onto the trailer could cause severe
injury.

5. Attach and tighten the winch bow strap.

6. Pull the trailer up the ramp and attach any additional tie-downs and

connect the trailer light harness.

7. Pull drain plugs.

!

WARNING

CAUTION

Scout Boats Section 10.qxd:Scout Boats Section 10.qxd 5/11/07 5:44 AM Page 7

«
...
99
100
101
102
103
...
»

Summary of Contents for 145

















































































































Reviews:

No comments

Related manuals for 145

Brand: Feathercraft Pages: 23

Brand: Feathercraft Pages: 23

Brand: SEATTLE Sailing Club Pages: 9

Brand: Pro-Line Boats Pages: 33

Brand: NorthStar Pages: 2

Brand: Quantum Sails Pages: 11

Brand: SEALINE Pages: 97

Brand: Honnor Marine Pages: 31

Brand: Gumotex Pages: 36

Brand: Gumotex Pages: 44

Brand: Vanguard Pages: 8

Brand: Vanguard Pages: 31

Brand: Quicksilver Pages: 51

Grand Soleil 50

Brand: Cantiere Del Pardo Pages: 124

Brand: Catalina Pages: 18

WaveRunner VXS 2014

Brand: Yamaha Pages: 98

Brand: Jeanneau Pages: 92

Brand: Malibukayaks Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands