Scout Boats 145 Owner'S Manual Download Page 24

Page: 24 / 112

Scout Boats

1-18

●

Water sport participants must wear a USCG approved
flotation device. A type III water ski vest is an approved and
practical PFD.

●

Keep at least 30 m (100 ft.) away from all other objects.

●

When water sporting have an experienced driver and aft
facing observer in the boat.

●

Never water sport in shallow water or at night.

●

Never jump from a moving boat.

●

Always keep a downed water sporter in sight.

●

Turn the motor OFF before you get close to someone in the
water.

GENERAL WATER SPORT
PRECAUTIONS

●

DO NOT ski in shallow water, close to shore, or in water where
you do not know the depth or what is beneath the surface.

●

DO NOT put your arm, head, or any other part of your body
through the handle-bridle of the ski line nor wrap the line around
any part of the body at any time.

KC-0271

WARNING

Chapter 1

Scout Boats Section 1.qxd:Scout Boats Section 1.qxd 5/11/07 5:35 AM Page 18

Summary of Contents for 145

















































































































Search results

Summary of Contents for 145

Reviews:

Related manuals for 145

Brands by name

Popular brands

Scout Boats 145, Owner'S Manual

Search results

Summary of Contents for 145

Reviews:

Related manuals for 145

Brands by name

Popular brands