Scout Boats 145 Owner'S Manual Download Page 57 | Manualshive

Page: 57 / 112

background image

Scout Boats

4-5

Operation

●

Keep the moving parts clean and lubricated.

●

Inspect the steering cables for kinks, damage, and corrosion.

The steering system must be in good operating condition for
safe boat operation. Frequent inspection, lubrication, and
adjustment by your dealer is recommended.

All boats have a tendency to wander somewhat at slow speeds. A natural
reaction to this effect is to steer the boat back and forth in an attempt to
compensate for wandering. Invariably, the compensation will result in
oversteer and only worsen the effect. Keep the steering wheel in the center
position, the boat will wander back and forth somewhat, but the overall
course will be a straight one.

!

WARNING

KC-1075

BACKING TO LEFT
Turn wheel to left—Stern
will pull to left.

RIGHT TURN
Turn wheel to right—Stern
will move to left

.

LEFT TURN
Turn wheel to left—Stern
will move to right.

Scout Boats Section 4.qxd:Scout Boats Section 4.qxd 5/11/07 5:39 AM Page 5

«
...
55
56
57
58
59
...
»

Summary of Contents for 145

















































































































Reviews:

No comments

Related manuals for 145

Brand: Parker Pages: 68

56 Side Console

Brand: YAMARIN Pages: 37

Brand: Williams Pages: 51

Brand: Lifetime Pages: 9

Brand: SEALINE Pages: 95

Brand: Aquabotix Technology Corporation Pages: 27

Brand: Ranger boats Pages: 80

Brand: GALA Pages: 10

2001 37-foot Pacific Trawler

Brand: Pacific Trawler Pages: 33

1997 Ski Nautique

Brand: CORRECT CRAFT Pages: 92

Brand: CORRECT CRAFT Pages: 248

Brand: Alliaura Marine Pages: 44

Brand: M.E.S. Marine Pages: 27

Offshore Series

Brand: Nauticstar Pages: 84

Brand: Zodiac Pages: 270

Brand: Laser Pages: 29

Brand: 3d Pages: 17

Brand: Quicksilver Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands