Scout Boats 145 Owner'S Manual Download Page 7 | Manualshive

Page: 7 / 112

background image

Scout Boats

1-1

The popularity of boating and other water sports has undergone an
explosion of growth in the past few years. Because of this, safety is an
important issue for everyone who shares in the use of our waterways.

This section covers general boating safety information. Throughout this
manual specific precautions and symbols identify safety related information.

The Safety Alert Symbol means ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!

Indicates the presence of a hazard which WILL cause SEVERE
injury, death or substantial property damage.

Indicates the presence of a hazard which CAN cause SEVERE
injury, death or substantial property damage.

Indicates the presence of a hazard which WILL or CAN cause
MINOR or MODERATE personal injury or property damage.

NOTICE

Indicates installation, operation or maintenance information
which is important but not hazard-related.

The precautions listed in this manual and on the boat are not all-inclusive. If
a procedure, method, tool or part is not specifically recommended, you must
satisfy yourself that it is safe for you and others, and that the boat will not
be damaged or made unsafe as a result of your decision. REMEMBER –
ALWAYS USE COMMON SENSE WHEN OPERATING YOUR BOAT!

!

DANGER

!

CAUTION

!

WARNING

!

Boating Safety

Chapter 1

Scout Boats Section 1.qxd:Scout Boats Section 1.qxd 5/11/07 5:35 AM Page 1

«
...
5
6
7
8
9
...
»

Summary of Contents for 145

















































































































Reviews:

No comments

Related manuals for 145

Brand: Gardasolar Pages: 69

Sea-Doo FT Series

Brand: BRP Pages: 212

Brand: Williams Pages: 51

Brand: Cobalt Digital Inc Pages: 128

Brand: Cobalt Digital Inc Pages: 124

Brand: grabner Pages: 12

Brand: Ranger boats Pages: 78

Brand: Fish Cat Pages: 6

Brand: Zoik Pages: 4

Brand: GALA Pages: 10

Brand: Access Dinghies Pages: 4

Brand: Mercury Pages: 123

Brand: NW Explorations Pages: 60

Brand: Gumotex Pages: 36

Brand: Gumotex Pages: 44

Brand: PATHFINDER Pages: 27

Brand: Pacific Northwest Pages: 16

Brand: Creek Company Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands