Scout Boats 145 Owner'S Manual Download Page 3 | Manualshive

Page: 3 / 112

background image

Scout Boats

i

Introduction

Welcome Aboard! This manual has been produced with the recreational
boater in mind, as a guide to safe operating practices, general boating reg-
ulations and proper maintenance techniques. Included with this manual
may be manufacturer literature for the engine, trailer and other major com-
ponents. To ensure each boating experience is a safe and enjoyable one,
please read all the materials carefully before operating your newly pur-
chased craft.

If this is your first time owning or operating this style of boat, it is recom-
mended you contact your dealer or local boating agency to find out how to
enroll in a boater safety course prior to taking to the water.

Please keep this manual onboard for future reference and pass it along to
the new owner if you ever decide to sell the craft.

Because of our policy of continuous product improvement, the illustrations
used in this manual may not be the same as on your boat and are intend-
ed only as representative reference views.

IDENTIFICATION NUMBERS

Safeguard information about your boat by recording the Hull Identification
Number (HIN) and model of your boat, and model and serial numbers of
the engine(s), trailer, and accessories on the inside front cover of this man-
ual. The HIN is located on the upper, starboard corner of the transom. The
HIN must be clearly visible and may not be removed, altered or tampered
with in any way as regulated by federal law.

The identification numbers are important! Keep a copy of these numbers
stored in a safe place off the boat. In case of theft, damage, etc., report
these numbers to the local authorities, your insurance agent and your
dealer.

© Ken Cook Co. 2002

Scout Boats Front Mat.qxd:Scout Boats Front Mat.qxd 5/11/07 5:33 AM Page i

«
1
2
3
4
5
...
»

Summary of Contents for 145

















































































































Reviews:

No comments

Related manuals for 145

Southern Pacific Shearwater 260 AL

Brand: Kiwi Yachting Pages: 20

Brand: Incept Pages: 8

Brand: Mercury Pages: 4

Brand: Seaboater Pages: 55

Brand: buster Pages: 203

Brand: Mercury Pages: 13

Brand: Yamaha Pages: 117

Offshore Series

Brand: Nauticstar Pages: 84

Brand: Jeanneau Pages: 106

SUN ODYSSEY 42 DS

Brand: Jeanneau Pages: 30

XL700Y WaveRunner

Brand: Yamaha Pages: 105

ANNEXE PLANCHER ALU 270

Brand: orangemarine Pages: 30

XL700 WaveRunner 2001

Brand: Yamaha Pages: 118

SUPERJET 700 2006

Brand: Yamaha Pages: 111

SUMMERLAND 40 LC

Brand: Fountaine Pajot Pages: 31

Helia 44 2013 Maple Cookie

Brand: Fountaine Pajot Pages: 31

Brand: Tribord Pages: 22

380 express series

Brand: Cruisers Yachts Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands