background image

Page 42 of 44

P/N 595189-01  Rev A  4/10

AcceSSorieS 

The following accessories are available: 
1.  Anti-Fog  Applique,  P/N  803939-02,  is  used  to  minimize  fogging  in 

the Scott-O-Vista facepiece. Anti-Fog Applique Installation Kit, P/N 

803939-25 contains 25 Appliques (P/N 803939-01) and instruc-

tions  for  new  or  replacement  installation. 

2.  Neck Strap, P/N 804088-01, is used to hold the facepiece in the 

standby position. 

3.  A variety of Lens Kits are available to allow installation of correc-

tive lenses in facepiece. 

4.  Clear  protective  Lens  Cover,  P/N  803941-25  (package  of  25)  to 

protect  facepiece  lens  from  external  scratching,  splatter,  paint 

spray, and abrasion. 

5.  Dual  airline  connection  hose  assembly  for  redundant  air  sup-

ply  hoses  or  to  facilitate  transfer  between  hoses.  H-Type  P/N 

804319-01 with standard Hansen fittings, S-Type P/N 804319- 02 

with standard Schrader fittings and HK-Type P/N 804319-03 with 

Hansen HK fittings. 

6.  Suit Pass-Thru, P/N 803620-01 with standard Hansen fittings and 

P/N 803620-02 with standard Schrader fittings. 

7.  Refer  to  the  FACEPIECE  FITTING  AND  FIT  TESTING  section 

of  this  instruction  for  information  about  Fit  Testing  Accessories. 

Consult your SCOTT distributor for details of availability and ap-

plication.

8.  A  variety  of  SCOTT  Full  Facepieces  are  approved  for  use  with 

the SKA-PAK AT. Consult your SCOTT distributor for details.

9.  Tool  Kit  with  instruction  for  Scott-O-Vista  and AV-2000  Mainte-

nance, P/N 26978-01. 

Summary of Contents for SKA-PAK AT













































Reviews: