background image

Page 37 of 44

P/N 595189-01  Rev A  4/10

WArning

reSPirATorS muST be Thoroughly dry 

before And during STorAge. moiSTure 

on  A  reSPirATor  in  beloW  freeZing 

TemPerATureS mAy cAuSe A mAlfunc-

Tion  of  The  reSPirATor  Which  could 

reSulT in SeriouS inJury or deATh.

WArning

The Self-conTAined Air SuPPly cylin-

derS muST be filled WiTh comPreSSed 

Air  Which  meeTS  The  reQuiremenTS 

for  grAde  d  or  higher  comPreSSed 

Air  AS  SPecified  in  The  comPreSSed 

gAS  ASSociATion  PublicATion  cgA 

g-7.1.  in  AddiTion  To  meeTing  The  re-

QuiremenTS  of  grAde  d  or  higher, 

The Air muST be dry To A deW PoinT of 

-65°  f  /  -54°  c  or  leSS.  fAilure  To  fill 

The  cylinder  WiTh  breAThing  Air  AS 

SPecified mAy cAuSe A mAlfuncTion of 

The  reSPirATor  Which  could  reSulT 

in SeriouS inJury or deATh.

WArning

The  noSe  cuP  ASSembly  iS  reQuired 

for  uSe  of  ThiS  reSPirATor  in  Tem-

PerATureS AT or beloW freeZing, 32° 

f / 0° c. fAilure To uSe  The noSe cuP  

mAy  cAuSe  obScured  viSion  And/or 

PArTiAl  or  comPleTe  blocKAge  of 

The  AirfloW  Which  could  reSulT  in 

SeriouS inJury or deATh.

loW TemPerATure oPerATion 

The respirator is NIOSH approved for use in temperatures to -25°F / 

-32° C. For temperatures below +32° F / 0° C, approval requires use 

of a Nose cup Assembly.
Respirators  intended  for  routine  use  and  respirators  not  routinely 

used  but  kept  for  emergency  use  should  be  located  in  areas  where 

the temperature is maintained above freezing, +32°F / 0° C. Where it 

is expected that the respirator will be used in ambient temperatures 

near or below freezing, the respirator shall be equipped with a Nose 

cup Assembly to reduce the formation of vision impairing mist or ice 

on the interior of the facepiece vision area. Anti-Fog Applique is also 

available  to  reduce  facepiece  fogging  in  conditions  above  freezing, 

+32°F / 0° C. See ACCESSORIES.

If a respirator may be unavoidably kept at a temperature below freez-

ing before the next use, special care MUST be exercised to be certain 

that all components of the respirator are THOROUGHLY DRIED after 

cleaning and before storage. 

If  a  respirator  has  been  unavoidably  kept  at  a  temperature  below 

freezing and it is not possible to bring it to room temperature before 

it is used, the following modification to the USE OF THE RESPIRA-

TOR section is required: 

 

WHEN  USING A  NOSE  CUP ASSEMBLY  OR AN ANTI-FOG 

APPLIQUE, do not exhale into the facepiece until the facepiece 

is completely donned and the nose cup, if used, is properly in 

place against the face. 

noTe

EFFECTIVENESS OF ANTI-FOG APPLIQUE IN PREVENTING FOG-

GING  OR  MOISTURE  CONDENSATION  ON  INTERIOR  SURFACE  OF 

FACEPIECE  ASSEMBLY  MAY  DIMINISH  WITH  REPEATED  USES 

OR  OVER  TIME.  THE  APPLIQUE  CAN  BE  REPLACED  IF  IT  HAS 

DIMINISHED  IN  EFFECTIVENESS  OR  SUSTAINED  SUBSTANTIAL 

DAMAGE. SEE ACCESSORIES SECTION FOR REPLACEMENT KIT 

INFORMATION. 

Whenever  use  of  the  respirator  is  anticipated  in  areas  at  or  below 

freezing,  the  facepiece,  regulator,  airline  connection  hoses  and  air 

supply  hoses  MUST  be  protected  against  exposure  to  water  during 

storage. 

Summary of Contents for SKA-PAK AT













































Reviews: