background image

Page 19 of 44

P/N 595189-01  Rev A  4/10

regulAr oPerATionAl inSPecTion 

conTinued on nexT PAge...

cAuTion

if The noSe cuP iS removed for inSPec-

Tion, mAKe cerTAin iT iS reASSembled 

correcTly  for  The  model  fAcePiece 

And STyle of noSe cuP. 

figure 10

checking voicemitter ducts

AV-3000 FACEPIECES ONLY

figure 11

blAcK nose cup

behind face Seal

figure 12

grAy nose cup

in fronT of face Seal

blAcK 

behind 

fAce SeAl

grAy

in fronT of 

fAce SeAl

AV-2000 STYLE FACEPIECES ONLY

Av-2000 nose cup

Always behind the face Seal

figure 13

9.  Inspect the nose cup for cuts or damage. Also look for any signs 

of damage to the facepiece port side of the nose cup where the 

regulator attaches. 

10. Check  that  the  nose  cup  is 

properly seated between the 

flanges  of  the  voicemitter 

ducts. See FIGURE 10. 

11. All SCOTT facepieces used with this respirator may be fitted with 

a nose cup. Verify that the Nose Cup is properly installed for the 

model  of  facepiece  being  used. A  Nose  Cup  is  standard  on  the 

SCOTT AV-2000®,  Weld-O-Vista,  and AV-3000®  full  facepieces 

and optional on the SCOTT-O-VISTA® full facepiece. 

a)   SCOTT AV-3000 and AV-3000 SureSeal Facepieces are avail-

able with two different styles of nose cup: a BLACK Nose Cup 

which  fits  behind  the  face  seal,  and  a  GRAY  Nose  Cup  which 

fits in front of the face seal. The BLACK Nose cup must be fit-

ted BEHIND the Face Seal as shown in FIGURE 11. The GRAY 

Nose Cup must be fitted IN FRONT OF the Face Seal as shown 

in FIGURE 12.

b)  The AV-2000,  the  Weld-O-Vista,  and  the  SCOTT-O-VISTA,  the 

Nose  Cup  always  goes  BEHIND  the  face  seal  REGARDLESS 

of the color of the nose cup. See FIGURE 13.

12. Verify that the facepiece is clean.

13. Adjust the head straps to the full outward position.

Proceed to 

OPERATIONAL TESTING OF THE RESPIRATOR

.

WArning

To  mAinTAin  nioSh  APProvAl,  An  Av-

3000 fAcePiece eQuiPPed WiTh A Sure-

SeAl  fAceSeAl  P/n  31001738  (SmAll), 

P/n  31001739  (medium),  or  P/n  31001740 

(lArge)  muST  be  uSed 

ONLY

  WiTh 

grey  noSe  cuP  P/n  31001043  (SmAll), 

P/n  31001044  (medium),  or  P/n  31001045 

(lArge). uSe of A non-APProved con-

figurATion  in  A  hAZArdouS  ATmo-

SPhere mAy reSulT in SeriouS inJury 

or deATh.

Summary of Contents for SKA-PAK AT













































Reviews: