manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 97 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 97

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 3-49  

 

3.5.1. 

Run / Service Menu 

The Service Run Menu enables the IRD user to control the operation of the IRD using the 
Service parameters (available in the PSI/SI tables from the broadcaster). When the IRD 
receives data from the service, it is provided on the relevant menu screen on the IRD Front 
Panel LCD. 

Figure  3-22 shows the menu tree flowchart for the Service Run Menu (password is required 
only if it was enabled previously). In addition, Figure  3-22 displays a typical LCD screen. 
The top line of the LCD displays the function and ID data. The bottom line displays the 
options available under the function. Table  3-17 describes the System Status Menu 
options. 

Figure  3-22: 

Service Run Menu Tree Structure 

    SERVICE

RUN

Teletext

SubService

DVB Service

Audio1

SubService

Data1

SubService

Data2

SubService

Store Decoded

Service to

Audio3

SubService

Audio2

SubService

DVB SbtL

Sub Service

TTX SbtL

Sub Service

IRD-2800 only

 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments