Scopus CODICO IRD-2600 User Manual Download Page 21

Page: 21 / 134

IRD-2600 / IRD-2800
Integrated Receiver Decoders

P/N 2349-72784-00

Page 1-9

1.2.2.

Basic Configuration

The IRD-2600 and IRD-2800 are delivered in a wide range of standard configurations, as
described in paragraph 1.2.3 ahead. Paragraph 1.2.4 describes the add-on options available
for the various configurations.

However, all IRD-2600 / IRD-2800 configurations provide the following basic features:

•

Profile: 4:2:0 (4:2:2 for IRD-2800 only)

•

2 slots DVB-CI Common Interface

•

Video formats: PAL B/G/M/N/D, NTSC, SECAM L/B/G/K1

•

Transcoding of 625/50 video formats (PAL B/G to/from PAL N and SECAM) and of
525/60 video formats (PAL M to/from NTSC)

•

Two Composite outputs; One S-VHS output

•

Full DVB compliance, as well as special modes for interoperability with certain non-DVB
IRDs

•

Audio (1st channel): one stereo pair, balanced output via XLR connectors; volume
adjustment.

•

Data channel: High-Speed Data @ RS-422 and Low-Speed Data @ RS-232

•

DVB descrambling, SimulCrypt Support, Scopus CAS-5000 descrambling, BISS
DSNG-CA

•

Over the air remote control; Over the air software upgrade

•

Teletext, VBI (WSS, Close Caption, VPS, VITS, VITC, SMC), analog, over composite

•

Selectable Audio/Video/Data combination mode OR Video-only OR Data-only OR
Audio-only mode.

•

Monitor and Control via RS-232 or RS-485 terminal (factory pre-set).

•

Auto-save of last configuration after power off; 140 pre-programmed setups (optional:
340).

•

Front panel control; Extensive Status indicators; Signal quality (Eb/N0), Video/Audio rate,
CA information.

•

RS-422 transport stream input

Summary of Contents for CODICO IRD-2600







































































































































Search results

Summary of Contents for CODICO IRD-2600

Reviews:

Scopus CODICO IRD-2600, User Manual, Page: 21 / 134

Search results

Summary of Contents for CODICO IRD-2600

Reviews: