manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 41 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 41

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 2-7  

 

2.4.5. 

Power Connection 

2.4.5.1.  Ground Connection 

Ground connection to the IRD is made by connecting an AC power cable to the IRD AC 
connector. If the IRD is fitted with a –48V DC power supply please follow the instruction 
provided under paragraph  2.4.5.3 below. 

When the IRD is rack mounted, the jackscrew (shown in Figure  2-3) must be connected to 
the rack housing, which in turn, should be properly grounded. 

Figure  2-3: 

IRD Jack Screw Ground Connection 

AC Power Supply Configuration

 

DC Power Supply Configuration

 

 

Ground

 

Jackscrew

 

Ground

Jackscrew

 

2.4.5.2.  AC Power Connector 

Connect the AC power cable to the IRD power connector at the rear of the unit. 
(see Figure  2-3) Connect the other end to the AC power source. 

2.4.5.3.  DC Power Connector 

In some cases the IRD is fitted with a –48V DC Power Supply as shown Figure  2-3 (DC 
Power Configuration). When this is the case please connect the power source as described 
below. 

To connect the –48V Power Supply: 

a.  Connect a (+) 48V DC source wire to the (+) contact on the power terminal board. 

b.  Connect a (-) 48V DC source wire to the (-) contact on the power terminal board. 

c.  Connect Grounding point wire to the (GND) contact on the power terminal board. 

 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments