manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 119 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 119

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 4-5  

 

4.4.3. 

BIT Stream Warning Messages 

The BIT Stream Warning messages are displayed on the IRD Main Status display.  
Figure  4-3 shows the structure of the message and Table  4-4 lists the messages and 
provides information about the detected failure types and possible reasons for the failure. It 
also advise the corrective action required. 

Figure  4-3: 

BIT Stream Warning Message Example 

BIT Stream Warning

Signal Not Recived

Top Line

Bottom Line

 

The top line displays the BIT Stream Warning Message  

The bottom line displays the problem type. 

Table  4-4:  

Bit Stream Warning 

PROBLEM 

TYPE 

POSSIBLE REASON 

CORRECTIVE ACTION 

RECEIVER

 

Signal Not Received 

Warning 

Input Signal Problem 

Set to correct parameters 

Demodulator Not Sync 

Warning 

Input Signal Problem 

Set to correct parameters 

Viterbi Not Sync 

Warning 

Input Signal Problem 

Set to correct Parameters 

Deinterleaver Not 
Sync 

Warning 

Input Signal Problem 

Set to correct Parameters 

Front End Not Locked 

Warning 

Input Signal Problem 
G703 Lock problem 

Set to correct Parameters, 
or repair in Scopus 
Network Technologies 

DECODER

 

No Sync (0x47) 
Detected 

Warning 

Bit Stream Problem 
Decoder Problem 

Set to correct Parameters, 
or call Scopus 
Professional Service. 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments