manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 81 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 81

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 3-33  

 

Table  3-10: 

Receiver Status Menu Parameters 

DSNG 

Q

P

S

K 

QA

M

 

AT

M

 

G

.703 

OPTION 

DESCRIPTION 

;

 

;

 

;

   

 

Frequency Tune 

Tune Frequency Received 
Displays the tuner programmed frequency of the signal 
received at the IRD (as set in the Receiver Configuration 
Menu, see paragraph  3.2.1). Number given in KHz. 

NOTE 

When the Frequency Drift Compensation function is activated, 

the displayed frequency is adjusted by the frequency offset 
during receiver operation. 

 

 

;

 

;

   

 

Frequency Offset 

Frequency Offset Value 
Indicates the frequency offset between the expected carrier 
frequency (as set in the Receiver Configuration Menu, see 
paragraph  3.2.1) and the carrier frequency of the recovered 
signal at the antenna. Number is given in KHz. 
 

 

 

;

   

 

QAM Mode 

QAM IRD Operational Mode 
Displays the QAM mode active in the QAM IRD receiver (as 
set in the Receiver Configuration Menu, see paragraph  3.2.1). 
Options available:

 

16 QAM, 32 QAM, 64 QAM, 128 QAM, 256 QAM.

 

 

;

   

 

 

 

Modulation Mode 

DSNG IRD Modulation 
Displays the modulation detected at the DSNG IRD receiver 
(as set in the Receiver Configuration Menu, see paragraph  
3.2.1). 
Options available: 

QPSK, 8PSK, 16QAM. 

 

;

   

 

 

 

Nyquist Filter 
Roll-Off 

Nyquist Filter Roll-Off 
Displays the current roll-off value of the Nyquist filter in the 
DSNG IRD (as set in the Configuration/Receiver Menu, see 
paragraph  3.2.1).  
Options available: 

25%, 35%. 

 

;

 

;

 

;

   

 

Viterbi Rate 

Viterbi Rate 
Displays the current rate for the Viterbi correction (as set in the 
Configuration/Receiver menu, see paragraph  3.2.1). 
Options available: 

1/2, 2/3, 3/4, 4/5, 5/6, 6/7, 7/8, 8/9. 

 

;

 

;

   

 

 

Spectral Inversion 

Spectral Inversion State 
Displays the current state of the spectral inversion function in 
the receiver (as set in the Configuration/Receiver menu, see 
paragraph  3.2.1). 
Options available: 

NORMAL, INVERTED. 

 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments