manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 73 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 73

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 3-25  

 

3.2.3. 

Configuration/System Menu 

The System Configuration Menu provides the IRD user the capability to set-up and 
configure the IRD operation. Figure  3-11 shows the menu tree of system level configuration 
functions available in the System Configuration Menu (password is required only if it was 
enabled previously). Table  3-9 describes each configuration function and the options 
available to the IRD user. 

The IRD Front Panel display, controls and keypad are used to scroll through the menu, 
view the options available and set the parameters of the configuration functions provided. 

Figure  3-11: 

System Configuration Menu Tree Structure 

Display

Contrast

Product Type

Software

Reset

Control Port

232 Syntax

Data1-HSD

Output Format

Control Port

Baud Rate

Data2-LSD

Output Format

Data1-HSD

Output Rate

Data2-LSD

Output Rate

DSNG-CA

Encryption Key

Default Data

Port

Injected ID

Control Port

Address

Session Word

         RECEIVER               DECODER             SYSTEM

          CONFIG                  STATUS              TEST             RUN

 

 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments