manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 14 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 14

 

User Manual 

Chapter  1. Overview

 

 

Page 1-2 

 

P/N 2349-72784-00 

 

1.1.1.1.  Inputs 

Decoder Inputs 

RS-422 Clock/Data Input 
 

 

DVB-ASI with Loop-through (optional) 

• 

Interface: Copper or Optical 

• 

TS bit rate: up to 54 Mbps 

 

Receiver Input Options 

DVB Satellite (QPSK) Front End 

• 

Frequency range: 950 -2150 MHz 

• 

Symbol rate range: 1 - 45 M Symbols/s 

• 

L-Band RF input with LNB control and Loop-through 
output 

 

 

DVB DSNG (8PSK, 16QAM and QPSK) Front End 

• 

Frequency Range: 950-2150 MHz 

• 

Symbol rate Range: 1 -45 Msym/s 

• 

2 L-Band inputs with LNB control 

 

 

DVB Cable (QAM) Front End 

• 

QAM demodulation: 16/32/64/128/256 

• 

VHF//UHF input: 50.5 – 858 MHz 

• 

Symbol Rate Range: 1-7 Msym/s 

 

 

Telecom G.703 Front End 

• 

Unframed PDH Data rates: E1,E2 or E3 

• 

FEC (optional): DVB-C FEC 

• 

Loop-through output 

 

 

DVB-PDH Front End 

• 

Interface: ATM AAL-1 

• 

Data rates: DS3 or E3 

• 

Loop-through output 

 

 

DVB-SDH SONET 

• 

TS bit rate: up to 58 Mbps 

• 

Interface: STM-1/OC-3, ATM AAL-1 

• 

Optical interface types: SM or MM, 1300 nm 

• 

Loop-through output 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments