manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 62 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 62

 

User Manual 

Chapter  3. Operation

 

 

Page 3-14 

 

P/N 2349-72784-00 

 

3.2.2. 

Configuration / Decoder Menu 

The Decoder Configuration menu provides the IRD user the capability to setup and 
configure the decoder in the IRD. Figure  3-6 shows the menu tree of configuration 
functions available in the Decoder Configuration Menu (password is required only if it was 
enabled previously).  

The IRD Front Panel display, controls and keypad are used to scroll through the menu, 
view the options available and set the parameters of the configuration functions provided. 

The Decoder Configuration functions are grouped into four groups and are described in the 
following sub-paragraphs:  

• 

Decoder/Stream functions configuration sub-menu, refer to paragraph  3.2.2.1. 

• 

Decoder/Common Interface (CI) functions configuration sub-menu, refer to paragraph  
3.2.2.2. 

• 

Decoder/Video functions configuration sub-menu, refer to paragraph  3.2.2.3. 

• 

Decoder/Audio functions configuration sub-menu, refer to paragraph  3.2.2.4. 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments