manualshive.com logo in svg

Scopus CODICO IRD-2600, User Manual, Page: 118 / 134

Share
Download
Scopus CODICO IRD-2600 User Manual Download Page 118

 

User Manual 

Chapter  4. Maintenance

 

 

Page 4-4 

 

P/N 2349-72784-00 

 

4.4.2. 

Hardware Failure Messages 

The Hardware failure messages are displayed on the IRD Main Status display as shown in 
Figure  4-2, which shows the structure of the messages. Table  4-3 lists the messages and 
provides information about the detected failure type and possible reasons for the failure. It 
also advise the corrective action required. 

Figure  4-2: 

Hardware Failure Message – example 

Hardware Failure

E2 Prom Failure

Top Line

Bottom Line

 

The top line displays the HARDWARE FAILURE Message. 

The bottom line displays the problem type. 

Table  4-3 

Hardware Failure Messages 

PROBLEM 

TYPE 

POSSIBLE REASON 

CORRECTIVE ACTION 

Demux-GTX Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Audio/Video Decoder Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Audio2 Decoder Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Video Encoder1 Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Video Encoder2 Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Audio1 Dac Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Video Output Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

SDI Output Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

E2Prom Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

XLINX1 Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

XLINX1 FIFO Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

XLINX1 RAM Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

XLINX2 (Option) Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

XLINX2 RAM Failure 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

FRONT END FAILURE 

Fault 

Hardware Problem 

Repair in Scopus Network 
Technologies 

Summary of Contents for CODICO IRD-2600







































































































































Reviews:

No comments