If receiver setup details are unavailable, you can perform a Quick Setup of your
Headend Satellite Receiver by following the step-by-step instructions in this Quick
Setup Guide. After performing the Quick Setup, you can change the current set-
tings to better suit your receiver operating requirements. If you are unsure about
which settings to use, contact your dealer/reseller or local service provider for as-
sistance. For complete receiver setup information, see the Model D9225 Headend
Satellite Receiver Installation and Operation Guide.
«$ERXWWKH9LGHR6WDQGDUG
The Video Standard used to operate the receiver is preset at the factory to either
NTSC (525-line) or PAL (625-line), depending on factory-installed options.
5HFHLYHU6WDUWXS
Step 1. Check your installation:
(a) Check that the receiver is correctly installed and connected to the
satellite LNB antenna, to other A/V equipment (as required) and to AC power.
(b) Verify that the satellite LNB power switch at the receiver rear panel is
correctly set (OFF to use the external LNB power source, or ON to use the
internal receiver LNB power source).
Step 2. Power-on the receiver: Press the STANDBY front panel button (1).
Step 3. Change the video standard [if required]:
(a) Press and hold the SELECT button (3), then (b) Press the Ï arrow button
(4) once to replace the current setting. (c) Press the Ï arrow button again
(4) to select the alternate video standard.
To use the ON/STANDBY, MENU, SELECT and arrow buttons
(1) Press STANDBY....................................................................................................................................
S TA N D B Y
(2) Press MENU............................................................................................................................................
M EN U
(3) Press SELECT........................................................................................................................................
(4) Press Ï and Ð........................................................................................................................
(5) Press Í and Î......................................................................................................................
4XLFN6HWXS*XLGH
C/Ku
FEC
S.Q.
M ODE
FREQ
SYM
SIG
POL
AFC
V IE W
A LT
1
2
3
4
5
6
7
8
9
0
A lt-1 M o de
A lt-2 M o de
BAUD
LO 1
LOCK
LO 2
W IDE
XOVER
V IE W
A LT
1
2
3
4
5
6
7
8
9
0
SEARCH
IMPORTANT: Only preauthorized subscriber services can be made available
for your Headend Satellite Receiver. If a unauthorized signal is present, a
warning message displays on the TV monitor. In this case, contact your
dealer/reseller or local service provider about satellite broadcast services
authorization.
Figure B. Front panel Alt-1 and Alt-2 Mode function buttons
IMPORTANT! The current Video Standard setting is used by the receiver
for correct display of the video (picture) only. The satellite receiver does not
convert from one Video Standard to another, such as from NTSC (525-line)
to PAL-B (625-line).
LN B P O W E R S W.
TO PC /W ORKS TATIO N
OR DATA TER MINAL
(OP TIO NAL)
TO SATE LL ITE AN TEN NA
STERE O/M ON O
AUD IO S ELECT SW.
AC POW ER SOC KET
TO L /R BAL ANCE D AU DIO INP UT
TERM IN AL BLO CK (C ABL E H EADE ND)
L/R BA LANCE D
AUD IO O UTP UT
LEVE L C O NTRO LS
TO VIDEO INP UT (CAB LE HEA DEND )
OR EXTE RNAL M ODU LATOR
TO AUD IO INPU T (CAB LE H EAD EN D)
OR EXTE RNAL M ODU LATOR
803-297
S cientific
Atlanta
Satellite Television Networks
S ATE LLIT E
LN B P W R
+ 13/+ 19 V 50 0mA M A X
A C IN 100 V-2 40V ~ A C
50/60 H z 1.4 A M A X
A U D IO
R
L
E XPA N S IO N P O R T
V ID EO
O N O F F
LN B P W R
Th is ap paratu s
mu st b e ea rth e d
Figure A. TV & RF plus optional connections
