Schweitzer Engineering Laboratories SEL-351R Instruction Manual Download Page 245 | Manualshive

Page: 245 / 620

background image

Date Code 20020215

Inputs, Outputs, Timers, and Other Control Logic

7-3

SEL-351R Instruction Manual

The relay processing interval is 1/4-cycle, so Relay Word bits IN101 through IN106 are updated
every 1/4-cycle. The optoisolated input status may have made it through the pickup/dropout
debounce timer (for settings less than 1/4-cycle) because these timers run each 1/16-cycle, but
Relay Word bits IN101 through IN106 are updated every 1/4-cycle.

If more than 1 cycle of debounce is needed, run Relay Word bit INn (n = 101 through 106)
through a SEL

OGIC

control equation variable timer and use the output of the timer for input

functions (see Figure 7.23 and Figure 7.24).

Input Functions

There are

no

optoisolated input settings such as:

IN101

=

IN102

=

Optoisolated inputs IN101 through IN106 receive their function by the way their corresponding
Relay Word bits IN101 through IN106 are used in SEL

OGIC

control equations.

Settings Examples

Figure 7.2: Circuit Breaker Auxiliary Contact and Reclose Enable Switch Connected to

Optoisolated Inputs IN101 and IN102

The example functions for inputs IN101 and IN102 are described in the following discussions.

Input IN101

In this example, Relay Word bit IN101 is used in the SEL

OGIC

control equation circuit breaker

status setting:

52A = IN101

Connect input IN101 to a 52a circuit breaker auxiliary contact.

«
...
243
244
245
246
247
...
»

Summary of Contents for SEL-351R













































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-351R

Brand: IBASE Technology Pages: 67

Brand: IBC Pages: 8

Brand: IAI Pages: 5

Brand: ABB Pages: 136

Brand: ABB Pages: 108

Brand: ebm-papst Pages: 10

Brand: Terrier Pages: 36

Brand: Pack Leader Pages: 99

Sunny Island MULTICLUSTER BOX 12.3

Brand: SMA Pages: 48

Brand: DBI SALA Pages: 32

Swegon Global PX

Brand: P.LEMMENS Pages: 24

Brand: A-PLUS AUTOMATION Pages: 28

Brand: Flexaseal Pages: 11

Brand: morse Pages: 8

Pneumatic Megatower

Brand: Larson Electronics Pages: 67

Brand: MAKSIWA Pages: 80

Brand: turck Pages: 36

Rosemount 485 Annubar

Brand: Emerson Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands