manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 6 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 6

SAFETY INSTRUCTIONS 

6 |   EN 

www.schmalz.com 

30.30.01.00226/03 

1 

Safety instructions 

1.1  Classification of safety instructions 

Danger 

This warning informs the user of a risk that will result in death or serious injury if it is not avoided. 

 

 

DANGER

 

 

 

 

Type and source of danger 

 

Consequence 

► 

Remedial action 

 

Warning 

This warning informs the user of a risk that could result in death or serious injury if it is not avoided. 

 

 

WARNING 

 

 

 

Type and source of danger 

 

Consequence 

► 

Remedial action 

 

Caution 

This warning informs the user of a risk that could result in injury if it is not avoided. 

 

 

CAUTION 

 

 

 

Type and source of danger 

 

Consequence 

► 

Remedial action 

 

Attention 

This warning informs the user of a risk that could result in damage to property if it is not avoided. 

 

ATTENTION

 

 

 

 

Type and source of danger 

 

Consequence 

► 

Remedial action 

 

 

Important information for efficient and trouble-free use.

  

 
 

 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments