Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 11

Page: 11 / 63

SAFETY INSTRUCTIONS

30.30.01.00226

/03

www.schmalz.com

EN | 11

DANGER

Unsuitable crane system

Risk of fatal injuries

►

Ensure that:



The crane system and hoist used have the appropriate dimensions.



The overall system (jib crane with tube lifter or other hoist) is
designed for use in potentially explosive atmospheres in accordance
with ATEX 1999/92 EC.

WARNING

Risk of falling objects

The integrity and function of the jib crane can no longer be guaranteed due to
unauthorized modifications or changes to the jib crane.

There is a risk that the load or hoist may fall, crushing body parts or
fatally injuring people in the vicinity.

►

Do not make any on-site modifications to the system.

►

Use only the original connections, mounting holes and attachment materials
that have been provided.

WARNING

Danger of death from falling if used as a means of transport for humans
or animals, or as a climbing aid

This can result in broken bones, serious injury or even death.

►

Use of the jib crane as a climbing aid or to transport humans or animals is
prohibited!

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Search results

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX

Reviews:

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 11 / 63

Search results

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX

Reviews: