manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 26 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 26

PRODUCT DESCRIPTION 

26 |   EN 

www.schmalz.com 

30.30.01.00226/03 

 Attachments 

2.6.11

Fig.1 

Fig.2 

Mobile base plate  

Anchor bolts 

Fig.3 

 

Shear connector 

 

 
Item 

Name 

1 

Crane column 

46 

Mobile base plate 

47 

Mounting foot 

48 

Anchor bolt 

49 

Shear connector 

 

 Electrical switches 

2.6.12

 

 

The crane mains supply switch is for 
disconnecting the power supply of electrical 
components (hoist, etc.). 
The crane mains supply switch does not contain 
any protective elements. 

A motor protection switch is used when a vacuum 
blower or a vacuum pump is used. The motor 
protection switch serves to switch off the vacuum 
generator and simultaneously protects it. The 
motor protection switch is designed for the 
connected vacuum generator. No further 
consuming devices may be connected to the outlet 
of the motor protection switch. 

 

47 

46 

1 

1 

48 

49 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments