manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 57 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 57

 

 

OPERATION 

30.30.01.00226

/03 

www.schmalz.com 

EN   | 57 

6.5  What to do in an emergency 

An emergency may occur: 

 

If there is a sudden power failure for the hoist. 

 

Take action as described in the “What to do in an emergency” section of the operating and 
maintenance instructions for your hoist. 

  Production of an ignition source in a potentially explosive atmosphere 

6.5.1

 

 

DANGER

 

 

 

 

Ignition sources 

 

Risk of explosion 

► 

When used in potentially explosive atmospheres: 

 

Preclude possible ignition sources (e.g. hot surfaces, open flames, hot 
gases or liquids, mechanically produced sparks, adiabatic compression, 
shock waves, exothermic chemical reactions, thermal reactions, the 
spontaneous combustion of dust, electric arcs or the discharge of static 
electricity or propagating brush discharges). 

 

Never allow the lifting device to be hit with force (spark discharge). 

 

Never strike the hoist with objects or tools (spark discharge). 

  Falling load 

6.5.2

 

 

WARNING 

 

   

 

Danger due to falling loads 

 

When operating a defective jib crane or hoist, the load or parts of the unit may 
fall and persons may be hit, injured or killed.  

 

 

►

 

Rectify any faults before starting the jib crane. 

►

 

Should faults occur during operation, switch the jib crane off and rectify the 
faults. 

 

 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments