Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 34 | Manualshive

Page: 34 / 63

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 34

INSTALLATION

34 | EN

www.schmalz.com

30.30.01.00226/03

5.4.1.2

Erecting the crane column in the foundation using anchor bolts

The number and order of the anchor bolts
depends upon the size of the crane and is
defined in the template

(

included in product range)

After the concrete has hardened, the nuts,
washers and template are removed.

Part no. of mounting kit

No. of anchor bolts

Depth T [mm]

L x W [mm]

14.04.02.10274

8 x M12

800

1,300 x 1,300

Template

T

Concrete groundwork: Mortar belonging to mortar group III in

accordance with DIN 1053

Anchoring: Anchor bolts in strength grade 8.8

Reinforcement:

B500

Crane column

Corner compression: max 200 kN/mm²

Foundation: C25/30

concrete Processing and

inspection in accordance

with DIN EN 206

Concrete cover: 5 cm on all sides

Position of

the pivot

«
...
32
33
34
35
36
...
»

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments