manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 31 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 31

 

 

INSTALLATION 

30.30.01.00226

/03 

www.schmalz.com 

EN   | 31 

5.1  Preparation of parts  

 

Identify all parts with the aid of the description in section 2. 

 

Sort all parts according to their intended use for the respective installation location. 

 

Do not start the assembly until you understand how 

all components

 are used. (All parts have 

been tailored to your requirements based on the project planning and parts list, i.e. 

there should 

be no parts left over

). 

Please contact the manufacturer in the event of any problems (telephone no. +49 7443 2403 0). 

5.2  Tool list 

 

1x combination wrench SW10, SW13, 2x SW19, SW24, SW36, SW46 

 

1x hexagon pin spanner 

 

1x spirit level 

 

1x torque wrench (23 

– 1,400 Nm) 

 

1x hexagon socket wrench bit SW10, SW13, SW19, SW24, SW36, SW46 

 

1x Phillips head PH2x100 

 

1x flat screwdriver 

 

1x carpet cutter 

 

1x wire cutter 

 

1x 10 m measuring tape 

 

1x plumb with centering discs (included in scope of delivery) 

 

1x plastic hammer 

 

1x hammer drill 

 

1x percussion drill ø14 mm, minimum 200 mm long  

 

1x blow gun (unoiled compressed air) 

 

1x cartridge gun 

 

 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments