manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 41 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 41

 

 

INSTALLATION 

30.30.01.00226

/03 

www.schmalz.com 

EN   | 41 

5.8  Mounting the crane jib on the crane column or wall bracket 

 

 

 
1.2 

Wall bracket/crane column lower 
bearing plate 

3.3 

Spherical bearings 

3.4 

Bolt 

3.6 

Bearing plate 

3.7 

Plastic film 

27 

Washer 

32 

Machine screws 

33 

Safety washer 

 

 

  Tool list 

5.8.1

1x

 

Allan key 

  Lower bearing mounting 

5.8.2

 

1.  Lift the crane jib with appropriate hoist to the height of the lower bearing plate of the wall 

bracket / crane column (1.2). 

2.  Push the bolt (3.4) in the bearing plate (3.6) until the lower edge of the bolts is flush with the 

lower edge of the bearing plate. The plastic film (3.7) holds the bolt and the bolt cannot slip 
into the pivot bearing. 

1.2  

3.4 

3.6 

1.2 / 2.2 

33 

3.4 

3.7 

32 

3.6 

27 

3.3 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments