manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 29 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 29

 

 

DELIVERY, PACKAGING AND TRANSPORT 

30.30.01.00226

/03 

www.schmalz.com 

EN   | 29 

4.4  Removal of crane components 

The packaging of the individual components and the disposable pallets must be opened carefully! 

 

Take care not to damage any of the components when opening the packaging with knives or 
blades. Do not take the parts out of the packaging until you are ready to begin installation (to 
protect against physical damage). 

 

Remove the packaging from the crane jibs and crane columns. 

 

Lay the components on a base, e.g. cardboard, so that they cannot be damaged. 

 

Avoid undertaking any other mechanical tasks in the area of the sections; otherwise there is a 
danger that chips and dirt could get into the section grooves. 

 

 

 

CAUTION 

 

 

 

Heavy components in the transportation box 

 

When opening the transportation box, parts can splinter or fall. This can cause 
crushing wounds and lacerations. 

 
► 

Wear protective work shoes (S1) and work gloves (safety category 2133).

 

 

 

ATTENTION

 

 

 

 

Improper removal of system from the transportation box

 

 

 

System damage 

► 

Do not apply force 

► 

Observe the instructions for removing the system from the transportation box 

 

 

The packaging material must be disposed of in accordance with national laws and 
guidelines. Labeled transport aids and safety mechanisms must be removed. 

 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments