manualshive.com logo in svg

Schick iPan, User Manual, Page: 26 / 35

Share
Download
Schick iPan User Manual Download Page 26

 

6.3  iPan USB Interface Upgrade 

Field updates to the iPan USB Interface can be accomplished by installing new firmware. 
When new firmware is available, it is typically provided with software releases and 
becomes part of the update to your existing system. In the event you are prompted to 
upgrade firmware, perform the steps provided below.   

 

USB Interface 
Firmware 
Upgrade 

Perform the following steps to start the USB Interface firmware upgrade 
procedure. 

 

Step Action 

1 

IMPORTANT! Close the CDR DICOM or EagleSoft program (if 
running) before continuing with the next step. 

2 

Verify that the iPan USB Interface is connected to the host 
computer. 

3 

Start the iPan Utility. 

4 

If the firmware version number is listed in red, click the Firmware 
Version button to upgrade. 

5 

If the CPLD version number is listed in red, click the CPLD 
Version button to upgrade. 

 

Example 

Pictured below is an example of the  iPan Utility, with the firmware upgrade 
buttons for the USB Interface highlighted. 
 

 

 

 

B1051601 Rev. –  

iPan User Guide

 

16 

Summary of Contents for iPan




































Reviews:

No comments