manualshive.com logo in svg

Schick iPan, User Manual, Page: 12 / 35

Share
Download
Schick iPan User Manual Download Page 12

 

1.4  About this Manual  

This User Guide is one of two documents needed to install the iPan system completely. 
Before performing the procedures in this document, you or a qualified service technician 
should complete the steps in the Installation Guide for your specific panoramic machine.  

Table 1

 provides a list of procedures and the documents where they are covered in detail. 

All of the procedures for installing iPan hardware may be found in your Installation 
Guide. This guide includes step-by-step instructions for installing the iPan hardware for 
your panoramic machine. Procedures for installing the iPan Interface driver can be found 
in this User Guide. 

 

Table 2

 provides a list of iPan-compatible panoramic machines and the iPan Installation 

document (Part Number B1051602) that describes the installation.  

1.5 References 

 

Table 1. List of Documents for Installing iPan 

Procedure Can be Found In . . .  

Document 

Install iPan Sensor and Codestrip 

iPan Installation Manual  

Install iPan USB Interface  

iPan Installation Manual  

Install iPan Power Supply  

iPan Installation Manual  

Install iPan Interface Driver  

This Manual 

 

Table 2. List of Compatible Panoramic Machines 

Description Can Be Found In . . .   

Document 

Panoramic Corporation PC-1000 

iPan Installation Manual  

Planmeca PM 2002 CC / EC 

iPan Installation Manual 

Sirona Orthophos 3 / Orthophos Plus 

iPan Installation Manual  

Villa Rotograph 

iPan Installation Manual 

Panoura SU-10 

iPan Installation Manual  

Siemens OP-5 / OP-10 

iPan Installation Manual 

Belmont X-Caliber 

iPan Installation Manual 

Gendex Orthoralix 9000 

iPan Installation Manual  

Instrumentarium OP-100 

iPan Installation Manual  

Soredex Cranex / BaseX 

iPan Installation Manual 

 

 

 

B1051601 Rev. –  

iPan User Guide

 

2 

Summary of Contents for iPan




































Reviews:

No comments