manualshive.com logo in svg

Schick iPan, User Manual, Page: 18 / 35

Share
Download
Schick iPan User Manual Download Page 18

 

4. Controls and LED Indicators 

4.1  iPan Power Supply 

The iPan Power Supply is connected by Sensor cable to the iPan Sensor and by CAT-5 
cable to the iPan USB Interface. The iPan Power Supply provides the necessary power to 
the iPan Sensor Module and accommodates the mains input voltage of 115 to 230V.  

 

 

 

Power Connector Side

 

 

Sensor Connector Side

 

 

 

Figure 2. iPan Power Supply  

 

 

Table 3. iPan Power Supply LED Indications  

Green LED 

Green LED 

Status 

ON 

ON 

Normal operation (± 15V available)   

Power, cable not connected to Power Supply or error 
condition 

OFF OFF 

4.2  iPan USB Interface 

The iPan USB Interface is connected by CAT-5 cable to the iPan Power Supply and by 
USB cable to a dedicated PC workstation. The iPan USB Interface provides several 
important functions, including Sensor diagnostics and field upgrades of firmware for the 
Sensor and the iPan USB Interface itself. 

 

B1051601 Rev. –  

iPan User Guide

 

8 

Summary of Contents for iPan




































Reviews:

No comments